| LCD Timeout Setting |
| [Commander Off] + [Volume-] + [Channel+] |
|
Use the (-) or (+) keys to change the value from 1 through 30 minutes.
|
| LCD Backlight Timeout Setting |
| [Commander Off] + [Light] |
|
Use the (-) or (+) keys to change the value from 1 through 60 seconds.
To enable or disable the fade feature (RM-AV3100 only), enter the combination above, press [COMMANDER OFF] once, then select the [FADE] option. Press [ON] to enable, or [OFF] to disable.
|
| LCD Backlight Brightness |
| [Commander Off] + [Light] + [Volume+] |
|
For the RM-AV3000 select [BRIGHT] or [DIM].
For the RM-AV3100, use the (-) and (+) keys to select a value from 1 to 10.
|
| LCD Backlight Auto-On Setting |
| [Commander Off] + [Light] + [Volume-] |
|
Select [ALL] to force the backlight on whenever the screen or certain hard buttons are tapped, or choose [LIGHT] if you only want to activate the backlight when the [LIGHT] hard button is pressed.
|
| Contrast Adjustment |
| [Commander Off] + [OK] |
|
Use the [CHANNEL UP/DOWN] buttons to adjust contrast levels to one of 16 levels.
|
| Beep Tone On/Off |
| [Commander Off] + [Muting] |
|
To enable the beep tone, press [MUTING] + [VOLUME+]. �BEEP ON� will appear on the display.
To disable the beep tone, press [MUTING] + [VOLUME-]. �BEEP OFF� will appear on the display.
|
| Sets the Clock |
| [Clock Display] + [Recall] |
|
Select either �STD Time� for Standard Time or �DS Time� for Daylight Savings time. Use the [RIGHT] and [LEFT] arrow keys to select the day, hour and minute, use [UP] and [DOWN] to change the value. Press [SET] to start the clock.
|
| Sets STD (Standard) Time |
| [Clock Display] + [Channel-] |
|
| Sets DS (Daylight Savings) Time |
| [Clock Display] + [Channel+] |
|
| Transmits or Receives Data from Another Remote |
| [Commander Off] + [Volume-] + [Channel-] |
|
Note: you can only transfer to/from identical models, for example you cannot transfer an RM-AV3000 to an RM-AV3100.
To transfer all information to another RM-AV3000 or RM-AV3100, first press the [UP] (send) arrow on-screen. Then press the �ALL� button. When the receiving remote is ready (see below), press the [ENTER] button to begin transmission. Arrows will show on-screen, when the transfer finishes [END] will appear. If the transfer fails, �NG� will flash.
To receive all information from another RM-AV3000 or RM-AV3100, first press the [DOWN] (receive) arrow on-screen. Then press the �ALL� button. To begin waiting to receive data, press the [ENTER] button. If �NG� flashes the remote must first be reset: press [CLEAR], followed by [RETURN], then try [ENTER] again. Arrows will show on-screen, when the transfer finishes [END] will appear. If the transfer fails, �NG� will flash.
To transfer one component to another RM-AV3000 or RM-AV3100, first press the [UP] (send) arrow on-screen. Then press the �COMPO� button, followed by the component you would like to send. When the receiving remote is ready (see below), press the [ENTER] button to begin transmission. Arrows will show on-screen, when the transfer finishes [END] will appear. If the transfer fails, �NG� will flash.
To receive one component from another RM-AV3000 or RM-AV3100, first press the [DOWN] (receive) arrow on-screen. Then press the �ALL� button, followed by the component button you would like to transfer to. To begin waiting to receive data, press the [ENTER] button. If �NG� flashes the component must first be reset: press [CLEAR], followed by [RETURN], then try [ENTER] again. Arrows will show on-screen, when the transfer finishes [END] will appear. If the transfer fails, �NG� will flash.
|
| Clears Customized Settings |
| [Commander Off] + [Muting], [Set], [Reset] |
|
To reset the entire remote control, press [ALL]. To finish, answer [YES] twice.
To reset all learned signals, macros and aliases for a single component, press [COMPO] followed by the component you would like to clear. To finish, answer [YES] twice.
To reset all components at a single time, hold the [DEL] key at the top of the screen and press [COMPO].
To reset a single system macro, press [SYSTEM] followed by the System Control button you would like to clear. To finish, answer [YES] twice. TIP: The setup menu�s �Reset� procedure will not remove the default �System Control 1� and �System Control 3� macros. To do so, enter macro recording mode, press and hold [DEL] and then select the button you want to reset.
To reset all system macros at a single time, hold the [DEL] key at the top of the screen and press [SYSTEM].
To reset a single timer, press [TIMER] followed by the timer button you would like to clear. To finish, answer [YES] twice.
To reset all timers at a single time, hold the [DEL] key at the top of the screen and press [SYSTEM].
|
| Locks the Remote from Changes |
| [Commander Off] + [Muting], [Lock] |
|
All of the remote�s setup menu options can be locked from further changes, one at a time. To do so, hold [LOCK] at the top right of the screen and the setup item to change. That item will stop flashing and can no longer be selected. To reverse this setting, repeat the procedure.
|
| Locks the Remote from Use |
| [Clock Display] + [Commander Off] |
|
To lock the remote hold the above button combination for two seconds. When the remote is locked the word �LOCK� will appear on-screen and it will beep twice if you try to use it.
To unlock the remote, hold [Commander Off] for 2 seconds.
|
| Resets the Remote to Factory Defaults |
| Note that this will remove absolutely all programming � use with caution! |
|
Remove at least one battery from the remote. Now, while holding the [VOLUME-] and [CHANNEL-] keys simultaneously, re-install the batteries and then release those two keys. The remote will display �EEPRON TEST OK SPI� on screen and flash the transmission icon continually. Again, remove at least one battery, re-install it, and the remote is cleared.
|
Previous page
