| Changes Sony Power On Setting |
| [Commander Off] + [Volume-] + [Component Select] |
|
Press once to enable the transmission of a Sony-only �Power On� discrete code whenever that device is selected. The LCD will show [POWER ON] on the top right. Press again to disable this feature - the LCD will show just [POWER].
This feature cannot be combined with any other Component Select-based feature.
|
| Copies a Component to Another Button |
| [Commander Off] + [New Component Select], [Old Component Select] + [New Component Select] |
|
To copy the [CD] device to the [VCR] button, press [COMMANDER OFF] plus [VCR], then hold [VCR] and press [CD]. The newly copied component name will flash on the top of the screen, alongside the hard button�s true label, which will appear solid.
If the remote beeps twice and flashes �NG�, the component you are copying to contains a macro or learned signal and must first be completely reset.
|
| LCD Timeout Setting |
| [Commander Off] + [Channel+] + [Volume-] |
|
Using the numeric keypad, select the number that corresponds to the screen timeout you would like � [1] for 10 minutes, [2] for 20 minutes, and so on. The number that does not flash represents the current value.
|
| LCD Backlight Timeout, Brightness & Auto-On Setting |
| [Commander Off] + [Light] |
|
To set the timeout, use the numeric keypad to select the number that corresponds to the backlight timeout you would like � [1] for 10 seconds, [2] for 20 seconds, and so on. The number that does not flash represents the current value.
To set the brightness level, use the [UP] and [DOWN] buttons to select the desired brightness level. There are 11 available settings.
To set the auto-on mode, press the [OFF] key in the upper-right corner of the screen. Press [1] to have the backlight come on only when you press the [LIGHT] button, or press [2] to have the light come on automatically upon any button press (except for volume and channel). The number that does not flash represents the current value.
|
| Beep Tone On/Off |
| [Commander Off] + [Muting] |
|
To enable the beep tone, press [Muting] + [Volume+]. �ON� will appear on the display.
To disable the beep tone, press [Muting] + [Volume-]. �OFF� will appear on the display.
|
| Changes Volume Control Setting |
| [Commander Off] + [Volume+] + [Volume-] |
|
Each time this button combination is entered, the setting toggles between �TV/Amp� or �Amp�. If the word �TV� appears on the LCD, all visual devices will use the television�s volume controls and all audio devices will use the amplifier�s volume controls. If �AMP� is shown, all devices will use the amplifier�s volume controls.
Note that this setting will not work with learned volume controls. You may also override it via aliases.
|
| Transmits or Receives Data |
| [Commander Off] + [Channel-] + [Volume-] |
|
To transfer all information to another RM-AV2500, first press the [UP] (send) button. Then press the [1] key. When the receiving remote is ready (see below), press the [ENTER] button to begin transmission. As information is transmitted, the corresponding component name disappears on screen. If the transfer fails, �NG� will flash.
To receive all information from another RM-AV2500, first press the [DOWN] (receive) button. Then press the [1] key. To begin waiting to receive data, press the [ENTER] button. If �NG� flashes the remote must first be reset: press [CLEAR], followed by [OK], then try [ENTER] again. As information is received, the corresponding component name appears on screen. If the transfer fails, �NG� will flash.
To transfer one component to another RM-AV2500, first press the [UP] (send) button. Then press the [2] key, followed by the component you would like to send. When the receiving remote is ready (see below), press the [ENTER] button to begin transmission. When the information is transmitted, the selected device name will disappear on screen. If the transfer fails, �NG� will flash.
To receive one component from another RM-AV2500, first press the [DOWN] (receive) button. Then press the [2] key, followed by the component button you would like to transfer to. To begin waiting to receive data, press the [ENTER] button. If �NG� flashes the component must first be reset: press [CLEAR], followed by [OK], then try [ENTER] again. When the information is received, the selected device name will disappear on screen. If the transfer fails, �NG� will flash.
|
| Locks the Remote from Changes |
| [Commander Off] + [Muting], [Power] |
|
All of the RM-AV2500�s setup options can be locked from change by pressing the upper-right (normally [Power]) key until it flashes �ON�.
To unlock remote setup, repeat the procedure until the upper-right key reads �OFF�.
|
| Locks the Remote from Use |
| [Commander Off] + [Power] (Upper Right LCD Key) |
|
To lock the remote, enter the above button combination. When the remote is locked, the word �OFF� will appear in the top right of the LCD and it will do nothing until the lock is removed.
To unlock the remote, repeat the procedure.
|
| Calibrates the Screen |
| [Commander Off] + [Menu] + [Exit] |
|
Press each of the four target dots as they appear in the outer corners of the screen with a pointy object, such as a stylus or tip of a pen. End the process by pressing the square that appears in the middle.
|
| Resets the Remote to Factory Defaults |
| Note that this will remove absolutely all programming � use with caution! |
|
Remove at least one battery from the remote. Now, while holding the [VOLUME-] and [CHANNEL-] keys simultaneously, re-install the batteries and then release those two keys. The remote will display �OK� on screen and flash the transmission icon continually. Again, remove at least one battery, re-install it, and the remote is cleared.
|
Previous page
